Crystal GaugeCalXP Rebuild Kit Manual de usuario descargar pdf

Service Instruction Sheet

Introduction

These instructions are intended for use with standard comparator rebuild kit (PN 4138) or the

Skydrol rebuild kit (PN 4158). Both rebuild kits contain all of the parts and tools required to rebuild

the GaugeCalXP™ pressure comparator. Rebuilds should be performed only by qualied personnel.

Following service instructions are for the standard comparator rebuild kit (PN 4138). If rebuilding the Skydrol

GaugeCalXP, cross reference the appropriate o-ring part numbers in the Parts List located on the last page.

Service Instructions

1 Remove all gauges and ttings from the

GaugeCalXP pressure comparator (gure 1).

2 Tip the comparator on its end to completely

drain the water or oil from the system.

Always dispose of uids in a responsible

manner.

3 Use a 3mm Allen key to remove the two (2)

cap screws securing the Reservoir to the

Main Seal Block, then lift to remove the Res-

ervoir and Reservoir o-ring (PN 2018)

(gure 2).

4 Remove the press-t Reservoir Vessel,

and replace the lower seal o-ring (PN 3303

or PN 3376) (gure 2).

Note:The GaugeCalXP is assembled with

a Reservoir o-ring in one of two sizes. Com-

pare your o-ring to the illustrated parts list

on page 6, to determine the appropriate

replacement size for your unit.

5 Use a 4- or 5mm Allen key to remove the

Handle Assembly bolt and washer(s), then

pull to slide the Handle Assembly from the

Piston Assembly (gure 3). Be sure to also

remove the Key from the Piston Assembly

Leadscrew (gure 3).

PRESSURE COMPARATOR

10000PSI–700bar

Gau

eCa

lxp

™

Figure 1

Figure 2

Figure 3

C R Y S T A L

engineering corporation

PSI

250

0 300

100

Gauge

Base

Reservoir

O-ring

(PN 2018)

O-ring

(PN 3303)

(PN 3376)

Handle

Key

Leadscrew

DESIGNED FOR USE WITH CRYSTAL PRESSURE FITTINGS

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Service Instruction Sheet

Service Instruction SheetIntroductionThese instructions are intended for use with standard comparator rebuild kit (PN 4138) or the Skydrol rebuild ki

Pagina 2 - C R Y S T A L

Page 2 • GaugeCalXP Service Instruction SheetC R Y S T A L engineering corporation6 Turn the comparator over to gain access to the underside of t

Pagina 3

GaugeCalXP Service Instruction Sheet • Page 3C R Y S T A L engineering corporation12 To remove the three (3) stainless steel Guide Rods, insert t

Pagina 4

Page 4 • GaugeCalXP Service Instruction SheetC R Y S T A L engineering corporation16 Remove the MPF-1/4FPT and MPM-MPM t-tings from the Rear Gau

Pagina 5

GaugeCalXP Service Instruction Sheet • Page 5C R Y S T A L engineering corporation23 From the front of the Fine Adjust body, remove the o-ring (P

Pagina 6 - Sizes to Scale

Page 6 • GaugeCalXP Service Instruction SheetParts ListO-ring 3303 / 416634.65mm x 1.78mm1.364in x 0.070inO-ring 3376 / 416735mm x 2.5mm1.378in x

Pagina 7

GaugeCalXP Service Instruction Sheet • Page 7C R Y S T A L engineering corporationHow to Contact Us:Phone (805) 595-5477Toll-Free (800) 444-1850

Pagina 8

Comentarios a estos manuales

Sin comentarios

Crystal GaugeCalXP Rebuild Kit Manual de usuario

Busca en linea o descarga Manual de usuario para Herramientas Crystal GaugeCalXP Rebuild Kit. Crystal GaugeCalXP Rebuild Kit User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Herramientas Crystal GaugeCalXP Rebuild Kit